Hi All,
Almost finished tweaking my new install. Coming from Win10.
I had screen tearing with Nvidia driver that I finally managed to solve but I could not get my monitor working 120Hz with HDMI. It worked under Windows and my monitor support 144Hz max. I know 144Hz only works with display port. Tried with Nouveau driver as well but same, only 60Hz is available. My laptop is an MSI CX62-2QD with Nvidia 940M
My Nvidia setting panel is looking a bit weird, I think a lot of things are missing from it eg. resolution setting, refresh rate setting...
https://drive.google.com/file/d/1HwbZK_R...sp=sharing
I tried to add custom refresh rates with xrandr but I could only manage to set it to 75Hz
xrandr
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 16384 x 16384
eDP-1-1 connected (normal left inverted right x axis y axis)
1366x768 60.00 + 48.00
1360x768 59.80 59.96
1280x720 60.00 59.99 59.86 59.74
1024x768 60.04 60.00
960x720 60.00
928x696 60.05
896x672 60.01
1024x576 59.95 59.96 59.90 59.82
960x600 59.93 60.00
960x540 59.96 59.99 59.63 59.82
800x600 60.00 60.32 56.25
840x525 60.01 59.88
864x486 59.92 59.57
800x512 60.17
700x525 59.98
800x450 59.95 59.82
640x512 60.02
720x450 59.89
700x450 59.96 59.88
640x480 60.00 59.94
720x405 59.51 58.99
684x384 59.88 59.85
680x384 59.80 59.96
640x400 59.88 59.98
576x432 60.06
640x360 59.86 59.83 59.84 59.32
512x384 60.00
512x288 60.00 59.92
480x270 59.63 59.82
400x300 60.32 56.34
432x243 59.92 59.57
320x240 60.05
360x202 59.51 59.13
320x180 59.84 59.32
DP-1-1 disconnected (normal left inverted right x axis y axis)
HDMI-1-1 disconnected (normal left inverted right x axis y axis)
HDMI-1-2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 531mm x 299mm
1920x1080 60.00 50.00 59.94
1920x1080i 60.00 50.00 59.94
1680x1050 59.88
1280x1024 60.02
1440x900 59.90
1280x960 60.00
1280x800 59.91
1152x864 75.00
1280x720 60.00 50.00 59.94
1024x768 70.07 60.00
800x600 60.32 56.25
720x576 50.00
720x480 60.00 59.94
640x480 66.67 60.00 59.94
720x400 70.08
1920x1080_75.00 74.91*
1920x1080_120.00 119.93
1920x1080_75.00 (0x264) 220.750MHz -HSync +VSync
h: width 1920 start 2064 end 2264 total 2608 skew 0 clock 84.64KHz
v: height 1080 start 1083 end 1088 total 1130 clock 74.91Hz
1920x1080_120.00 (0x280) 369.500MHz -HSync +VSync
h: width 1920 start 2080 end 2288 total 2656 skew 0 clock 139.12KHz
v: height 1080 start 1083 end 1088 total 1160 clock 119.93Hz
I have this error message when I try to use the new mode.
xrandr --output HDMI-1-2 --mode 1920x1080_120.00
xrandr: Configure crtc 1 failed
xrandr --props
Screen 0: minimum 8 x 8, current 1920 x 1080, maximum 16384 x 16384
eDP-1-1 connected (normal left inverted right x axis y axis)
EDID:
00ffffffffffff0030e4af0400000000
00190104952213780a6bc59359549027
1b505400000001010101010101010101
010101010101d01d56f4500016303020
350058c21000001ad91756f450001630
3020350058c21000001a000000fe004b
39364432803135365748550a00000000
00004131940010000009010a202000fe
PRIME Synchronization: 1
supported: 0, 1
scaling mode: Full aspect
supported: Full, Center, Full aspect
max bpc: 12
range: (6, 12)
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
link-status: Good
supported: Good, Bad
CONNECTOR_ID: 68
supported: 68
non-desktop: 0
range: (0, 1)
1366x768 60.00 + 48.00
1360x768 59.80 59.96
1280x720 60.00 59.99 59.86 59.74
1024x768 60.04 60.00
960x720 60.00
928x696 60.05
896x672 60.01
1024x576 59.95 59.96 59.90 59.82
960x600 59.93 60.00
960x540 59.96 59.99 59.63 59.82
800x600 60.00 60.32 56.25
840x525 60.01 59.88
864x486 59.92 59.57
800x512 60.17
700x525 59.98
800x450 59.95 59.82
640x512 60.02
720x450 59.89
700x450 59.96 59.88
640x480 60.00 59.94
720x405 59.51 58.99
684x384 59.88 59.85
680x384 59.80 59.96
640x400 59.88 59.98
576x432 60.06
640x360 59.86 59.83 59.84 59.32
512x384 60.00
512x288 60.00 59.92
480x270 59.63 59.82
400x300 60.32 56.34
432x243 59.92 59.57
320x240 60.05
360x202 59.51 59.13
320x180 59.84 59.32
DP-1-1 disconnected (normal left inverted right x axis y axis)
PRIME Synchronization: 1
supported: 0, 1
max bpc: 12
range: (6, 12)
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
CONNECTOR_ID: 74
supported: 74
non-desktop: 0
range: (0, 1)
HDMI-1-1 disconnected (normal left inverted right x axis y axis)
PRIME Synchronization: 1
supported: 0, 1
max bpc: 12
range: (8, 12)
content type: No Data
supported: No Data, Graphics, Photo, Cinema, Game
Colorspace: Default
supported: Default, SMPTE_170M_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, opRGB, BT2020_CYCC, BT2020_RGB, BT2020_YCC, DCI-P3_RGB_D65, DCI-P3_RGB_Theater
aspect ratio: Automatic
supported: Automatic, 4:3, 16:9
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
CONNECTOR_ID: 80
supported: 80
non-desktop: 0
range: (0, 1)
HDMI-1-2 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 531mm x 299mm
EDID:
00ffffffffffff00047272044c992090
021d010380351e782a6435a5544f9e27
125054b30c00d1c081c081009500b300
81808140714f866f80a0703840403020
3500132b2100001a023a801871382d40
582c4500132b2100001e000000fd0030
781eb41e000a202020202020000000fc
0041636572205846323430480a2001ad
020329f14b0102030411121305141f10
230907078301000067030c001000b83c
681a000001013078008c0ad08a20e02d
10103e9600132b21000018011d007251
d01e206e285500132b2100001e8c0ad0
90204031200c405500132b2100001800
00000000000000000000000000000000
0000000000000000000000000000000c
PRIME Synchronization: 1
supported: 0, 1
max bpc: 12
range: (8, 12)
content type: No Data
supported: No Data, Graphics, Photo, Cinema, Game
Colorspace: Default
supported: Default, SMPTE_170M_YCC, BT709_YCC, XVYCC_601, XVYCC_709, SYCC_601, opYCC_601, opRGB, BT2020_CYCC, BT2020_RGB, BT2020_YCC, DCI-P3_RGB_D65, DCI-P3_RGB_Theater
aspect ratio: Automatic
supported: Automatic, 4:3, 16:9
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
CONNECTOR_ID: 86
supported: 86
non-desktop: 0
range: (0, 1)
1920x1080 60.00 50.00 59.94
1920x1080i 60.00 50.00 59.94
1680x1050 59.88
1280x1024 60.02
1440x900 59.90
1280x960 60.00
1280x800 59.91
1152x864 75.00
1280x720 60.00 50.00 59.94
1024x768 70.07 60.00
800x600 60.32 56.25
720x576 50.00
720x480 60.00 59.94
640x480 66.67 60.00 59.94
720x400 70.08
1920x1080_75.00 74.91*
1920x1080_120.00 119.93
1920x1080_75.00 (0x264) 220.750MHz -HSync +VSync
h: width 1920 start 2064 end 2264 total 2608 skew 0 clock 84.64KHz
v: height 1080 start 1083 end 1088 total 1130 clock 74.91Hz
1920x1080_120.00 (0x280) 369.500MHz -HSync +VSync
h: width 1920 start 2080 end 2288 total 2656 skew 0 clock 139.12KHz
v: height 1080 start 1083 end 1088 total 1160 clock 119.93Hz
Any help would be appreciated. Thanks
Hello Everyone,
Earlier I tried to search for install Facebook Messenger on the main forum. This results in no hits. Hopefully, I am not asking a question that has already been answered. However, if it has, then please just include a link to the answer in this topic.
I wish to install the Facebook Messenger software on Linux Lite. How may I accomplish this goal?
Thank you.
I'm debating on getting a writing tool that not as bloated as libreoffiice for my book writing sessions . Theses two came up in the repos.
Sent from my moto g power using Tapatalk
[size=1em]I am following the instructions to update the BIOS at https://www.dell.com/support/kbdoc/en-us...e%20Device. When I boot to the USB created using UNetBootin and I select FreeDOS, I get "Invalid or corrupt kernel image."[/size]
[size=1em]For the record, the md5sum and sha256sum are good for the FreeDOS file I downloaded, and I am using the binary for UNetBootin from https://unetbootin.github.io/.[/size]
[size=1em]My laptop is a Latitude E6430, and I used the USB 2.0 port to create and boot to the bootable USB.[/size]
[size=1em]I am running LUKS full disk encryption. I'm not sure if a BIOS update will run with that in play. If LUKS is the problem, is there a way to suspend it so that I can go through with the BIOS update?[/size]
Hello All
here I lile to share an interesting feature of libereoffice
It s a PDF export as hybrid PDF it means that the PDF file will be full editable
https://wiki.documentfoundation.org/Docu...AHybridPDF
Greetings
Nanayaw
I have just installed Linux Lite on an old desktop PC.
It uses a TP-LINK TL-WN722N V2.0 USB adapter for WIFI access.
The wifi seems to be working fine, and I was even able to access local shared files over the wifi.
BUT, the internet connection doesn't seem to be working.
I can't see anything obvious wrong.
I connected to the modem with an ethernet cable, and performed all the updates, but to no avail.
Any suggestions?
I am trying to install linux lite on an old desktop PC and I keep getting this message when installing:
The 'grub-efi-amd64-signed package' failed to install into /target/.I have tried all the different bios settings and additional partitions that were suggested online, but nothing worked.
Does anyone have any idea how to get past this issue?
After update yesterday, Firefox will not start.
My netbook ( Eee PC 900, 1GB Ram, 32bit only CPU) runs 3.8 32bit
Firefox ran after an update 2 days ago, I believe the FF was V84.0.2
Installed 3.8 on a Oracle VirtualBox 6.1.16, now & updated and the exact same results, FF won't open.
Don't know what to do now.
Hello Everyone,
I tried searching for this on the forums, but I suck at searching for pretty much anything. If this question is in another topic, please include a link to the topic, so I may read your answer there. Otherwise, I look forward to reading your responses on this topic.
I will admit there are things I miss about Windows XP and 7. On either of them, I would double click "My Documents". Then a window would appear, which shows me the contents of "My Documents". Eventually, I would navigate to a particular folder. Back then, I would right click as I viewed the contents of the folder, and it would give me several options. Thanks to having Microsoft Office installed on that computer, I would have the option to create a new Word, Excel, PowerPoint, and perhaps more types of documents. I would love to duplicate this behavior on Linux Lite. However, it would not be Microsoft Office documents, but instead Linux Lite's equivalent office software. On this computer, if I were looking at folder xyz, in a window, then I would be able to right click with the mouse, and be able to create a Word Processor document in the folder where I right clicked. Here are the steps in order and the desired goal:
1. Open "Documents".
2. Navigate to Dir XYZ.
3. Right click inside window showing me Dir XYZ.
4. See several options in right click menu.
5. Click on Word Processor menu option.
6.Goal: New Word Processor Document appears in Dir XYZ.
Please note, I said Dir XYZ, because I don't want to tell you the folders I have created on my computer. I hope this nomenclature works well for the both of us.
How would I go about getting Linux Lite to know what I wish to see in the mouse - right click menu?
If this is answered in another topic, please include a link to that topic so I may finally read the answer there. If this is the case, then I am sorry that I suck at searching for preexisting topics. Whether another topic provides the tutorial I now seek or not, I very much look forward to learning how to accomplish the goal mentioned in this topic.