Linux Lite Forums
Software - Support => Installing Linux Lite => Topic started by: Feather on June 29, 2022, 05:38:44 AM
-
Hi
I've been successfully running 4.8 on Asus E203
But can't, as yet, install 6.0 from dvd iso on Asus BR1100F
Works live.
New laptop with windows 10 pre-installed - windows has never been opened.
uefi - realtek pxe ipv4
Erase partitions and install Linux
It takes 20 minutes to get to install now:
Partition #1 esp
Partition #2 ext4
then 'where are you?', then, 'who are you?'
stops here:
'creating ext4 file system partition #2'
ntpd 2039 error resolving pool temporary failure in name resolution
dma read NO_PASID fault address fault reason 0x06 pte read access is not set
source id 7541 was not found when attempting to remove it.
Thoughts?
-
Might be worth looking at the disk.
Boot from Live media
Menu>Settings>Disks
On the Left, select the hard disk that you are installing to
Click the three dots (Drive Options) towards the right side of the Disks top bar
On the pull down select 'SMART Data and Self tests'
Look at the Overall Assessment and the Reallocate Sector Count (5)
-
smart data and self tests is greyed out.
Tried booting from check for file corruption - booted fine. The install still stops here:
'creating ext4 file system partition #2'
-
Do you know what type of disk it is ?
Did the new laptop work ok out of the box ?
As you've already tried "erase and install" from the install process, I'd be tempted to use gparted to tidy up before trying to install again.
Boot a live session then click
Menu->System->Partition Drives
This will open gparted.
Make sure the target drive is selected then click
Device>Create partition table, select GPT, then apply.
Once that's done try the install again.
-
Still stopping in the same place :(
linux kernel DMAR: DRHD: handling fault status reg 3
linux kernel DMAR: [dma read NO_PASID] request device [00.1a0] fault addr 0xfc483000 [fault reason 0x06] PTE read access is not set.
updating the bios to 313
never tried the laptop in windows - went straight to the bios screen
dvd - DS8A2L (old!)
-
I meant what type of hard disk, not DVD.
Several things you've mentioned might indicate that the hard disk or the system access to it may not be working properly.
Windows not booted on original
Hang when creating partition
SMART not available
Did you buy it new and is it under warranty ?
-
Brand new from Asus.
emmc 64gb G1J38E
from the settings - disk:
file system partition 1
537MB
FAT (32 bit version) - not mounted.
device /dev/mmcblk0p1
partition type efi system
partition 2 62gb unknown
uefi realtek pxe ipv4 was in the bios boot menu - now the boot menu is empty :(
-
Should I try this, or something similar?
https://superuser.com/questions/1688659/128gb-emmc-drive-on-asus-laptop-unable-to-format-to-ext4
Or, install an M.2 2280 PCle 3.0x4 ssd?
-
I can't say which worked, or it was the combination? - but it is installed.
313 bios update
Additional 250gb Samsung 980 M.2 2280 pcle 3.0x4 - bought a screw from ebay, you don't need the stand off.
Now booting from the original board.
USB install using 'etcher' - instead of dvd.
Only thing I very briefly see, during start up, is 'ACPI ERROR'
Just have to work out how to get Firefox and Thunderbird to auto start? Any ideas?
-
Well done on getting it working.
Managing applications to automatically run can be done via
Menu->Settings->Session and Startup
Select the Application Autostart tab then add