I have just installed Linux Lite on an old desktop PC.
It uses a TP-LINK TL-WN722N V2.0 USB adapter for WIFI access.
The wifi seems to be working fine, and I was even able to access local shared files over the wifi.
BUT, the internet connection doesn't seem to be working.
I can't see anything obvious wrong.
I connected to the modem with an ethernet cable, and performed all the updates, but to no avail.
Any suggestions?
What DNS are you using?
What is the output of:
and
with my ethernet cable connected
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.254 0.0.0.0 UG 100 0 0 enp3s0
0.0.0.0 192.168.1.254 0.0.0.0 UG 600 0 0 wlxd46e0e1f45bb
192.168.1.0 0.0.0.0 255.255.255.0 U 100 0 0 enp3s0
192.168.1.0 0.0.0.0 255.255.255.0 U 600 0 0 wlxd46e0e1f45bb
ifconfig
enp3s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.84 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::a99b:582e:2d35:ad69 prefixlen 64 scopeid 0x20<link>
ether 44:8a:5b:26:2b:22 txqueuelen 1000 (Ethernet)
RX packets 17876 bytes 8150271 (8.1 MB)
RX errors 0 dropped 6 overruns 0 frame 0
TX packets 34192 bytes 41935685 (41.9 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 794 bytes 65604 (65.6 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 794 bytes 65604 (65.6 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlxd46e0e1f45bb: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.78 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::3d4f:b860:d8b2:493d prefixlen 64 scopeid 0x20<link>
ether d4:6e:0e:1f:45:bb txqueuelen 1000 (Ethernet)
RX packets 6019 bytes 1005852 (1.0 MB)
RX errors 0 dropped 3342 overruns 0 frame 0
TX packets 422 bytes 71594 (71.5 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
without the ethernet cable:
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.254 0.0.0.0 UG 600 0 0 wlxd46e0e1f45bb
192.168.1.0 0.0.0.0 255.255.255.0 U 600 0 0 wlxd46e0e1f45bb
ifconfig
enp3s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 44:8a:5b:26:2b:22 txqueuelen 1000 (Ethernet)
RX packets 18112 bytes 8197332 (8.1 MB)
RX errors 0 dropped 6 overruns 0 frame 0
TX packets 34314 bytes 41949566 (41.9 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 884 bytes 72432 (72.4 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 884 bytes 72432 (72.4 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlxd46e0e1f45bb: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.78 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::3d4f:b860:d8b2:493d prefixlen 64 scopeid 0x20<link>
ether d4:6e:0e:1f:45:bb txqueuelen 1000 (Ethernet)
RX packets 6480 bytes 1078140 (1.0 MB)
RX errors 0 dropped 3548 overruns 0 frame 0
TX packets 450 bytes 75672 (75.6 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
(01-31-2021, 04:15 AM)Jerry link Wrote: [ -> ]What DNS are you using?
Not sure what you're like installing drivers, but this looks very well suited and optimized -
https://github.com/abhijeet2096/TL-WN722N-V2 only do 1 -7, nothing else! Hopefully it will work with the current kernel. Take note of the section 'Activating/Deactivating LED' before you do step 3.
Thank you for finding that.
I might need a bit of help understanding what i am doing.
When I try to do step 4, I get this message:
(also, see attached make.log file)
Code:
sudo dkms build -m 8188eu -v 1.2
Kernel preparation unnecessary for this kernel. Skipping...
Building module:
cleaning build area...
'make' all.........(bad exit status: 2)
Error! Bad return status for module build on kernel: 5.4.0-65-generic (x86_64)
Consult /var/lib/dkms/8188eu/1.2/build/make.log for more information.
That one installed successfully, but unfortunately the problem persists.
It is quite interesting that the internet works fine over ethernet cable, and the WIFI seems to work fine for shared local files etc., but the internet just won't work over the WIFI. :-\