07-13-2020, 07:25 PM
07-13-2020, 07:43 PM
(07-13-2020, 07:25 PM)FreddyM link Wrote: [ -> ]Hallo
i have new installed LL5, everthing work fine, but the boot entry show me "Ubuntu"and not "Linux Lite".
Best regards from Austria
Hi!
Use Lite Tweaks and choose "Boot up Fix - Restore the boot splash to Linux Lite."
Press than "Begin".
That is all!

Regards!

07-13-2020, 10:50 PM
(07-13-2020, 07:25 PM)FreddyM link Wrote: [ -> ]Hallo[member=6878]FreddyM[/member]
i have new installed LL5, everthing work fine, but the boot entry show me "Ubuntu"and not "Linux Lite".
Best regards from Austria
As per the release announcements... https://www.linuxliteos.com/forums/relea...-released/
Known Issues:
...
...
Grub menu shows Linux Lite as 'Ubuntu'. After you install Linux Lite, you can change Grub to show 'Linux Lite':
- Open /etc/default/grub as Administrator.
- Comment out: GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` and leave GRUB_DISTRIBUTOR='Linux Lite' uncommented.
- Should look like:
GRUB_DISTRIBUTOR='Linux Lite'
#GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
and finally:
Code:
sudo update-grub
Looks better when you are dual-booting with Windows too.
07-14-2020, 07:55 AM
(07-13-2020, 10:50 PM)firenice03 link Wrote: [ -> ][...]
- Open /etc/default/grub as Administrator.
- Comment out: GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` and leave GRUB_DISTRIBUTOR='Linux Lite' uncommented.
- Should look like:
GRUB_DISTRIBUTOR='Linux Lite'
#GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
and finally:
[...]Code:sudo update-grub
I'd rather KISS!
(07-13-2020, 07:43 PM)Şerban S. link Wrote: [ -> ][...]
Use Lite Tweaks and choose "Boot up Fix - Restore the boot splash to Linux Lite." [...]


07-14-2020, 03:29 PM
Hallo
"Boot up fix" don't work, but the hint from "firenice03" work well.
Best regards
"Boot up fix" don't work, but the hint from "firenice03" work well.
Best regards
07-14-2020, 03:42 PM
I like to KISS too... But (should folks come along)
The OP asks to CHANGE the boot entry (GRUB) from Ubuntu to Linux Lite..
Your post tells him how to reset the Boot Splash ("feather") screen - this can happen when one see's a blank or changed boot splash screen..
The instruction provided are verbatim from the LL5.0 - Release Announcements (if there was a simpler way I'm sure it be listed there)
Also see the Boot Up Fix (Splash) - https://www.linuxliteos.com/forums/linux.../#msg12383
Added Bootup Fix - restores the Linux Lite splash screen if it gets overwritten by a system update (Ubuntu splash).
As I was posting:
Good to hear you have it worked out!!! As its been corrected you can mark the thread resolved
The OP asks to CHANGE the boot entry (GRUB) from Ubuntu to Linux Lite..
Your post tells him how to reset the Boot Splash ("feather") screen - this can happen when one see's a blank or changed boot splash screen..
The instruction provided are verbatim from the LL5.0 - Release Announcements (if there was a simpler way I'm sure it be listed there)
Also see the Boot Up Fix (Splash) - https://www.linuxliteos.com/forums/linux.../#msg12383
Added Bootup Fix - restores the Linux Lite splash screen if it gets overwritten by a system update (Ubuntu splash).
As I was posting:
(07-14-2020, 03:29 PM)FreddyM link Wrote: [ -> ]
Hallo
"Boot up fix" don't work, but the hint from "firenice03" work well.
Best regards
Good to hear you have it worked out!!! As its been corrected you can mark the thread resolved

07-14-2020, 06:54 PM
(07-14-2020, 03:42 PM)firenice03 link Wrote: [ -> ][...] this can happen when one see's a blank or changed boot splash screen.. [...]
Yes, Sir! ;D
I forgot I used "Grub Customizer" and then after installing LL 5.0 it had "Delay=0" so it actually entered the boot sequence without asking what to load.
Since I never bothered because GRUB can be accessed if necessary, I forgot about multi-boot. Lately, I gave up installing dual/multi boot. I prefer using an external drive and boot from it. It's safer and easier to backup (CloneZilla) this way.
Sometimes is very handy to have a (different) setup on an external, for some specific tasks.
Besides, it only takes a few seconds to switch from one setup to the other.
Here is for one:
I have two graphic cards and would like to see if I can use "Hybrid Graphics". It is far morre convenient to do this on a "clean install", than mess with the main installation.
So probably my approach was flawed by some old habits of mine: backup everything than change whatever, then if something goes sideways..., restore.
Thanks for pointing out the difference!

All the best!
